1/6/2024 0 Comments Shadow etuner install![]() The server provides desktop and in-game screen capture support to the client applications. ![]() The server can be also used as a standalone framerate monitoring solution and display own framerate statistics in the On-Screen Display. Display in DirectX and OpenGL applications.The clients can display any text info in the On-Screen The server provides On-Screen Display support to the client applications.The clients can use the statistics to determine if any 3D applications are currently running and apply different hardware profiles depending on it. The server provides 3D acceleration usage statistics to the client applications.The statistics can be rendered in On-Screen Display or provided to client applications connected to the server. Framerate and frametime statistics is being collected for DirectX, OpenGL and VULKAN applications. The server provides framerate and frametime monitoring support to the client applications. To spare the battery life, take the cable out, when not used. Note: The battery turns on automatically, as soon as you plug the instrument cable into the endpin. Connect the endpin to an appropriate amplifier. Make sure the strings do not pull the bridge saddle forward in neck direction (Fig. Mount the strings and tune your instrument. Use included cable holders to fix the cables inside the guitar. Check if the pickup and preamp are correct working and fix the screws of the preamp. Connect pickup cable and endpin output cable to the preamp and mount the preamp into the guitar’s side. Place the preamp so that it fits precisely and drill with 1mm drill diameter four outside holes to fix the preamp. Cut out hole in guitar body following the inside edge of the black line of the template. Place the template sticker between the stripes of tape with the center marks lined up. Measure the total width of the guitar side and mark the center point. Mark the positions of the ends of the preamp and place masking tape across the side of the guitar. Onboard Preamp Installation: Slide the preamp along the guitar side to find the point where the curve of the preamp matches the curve of the guitar. Place the double cable holder to the side of the guitar and secure the endpin cable and the pickup cable into it. Failed to secure the wire may produce bizarre audio consequences. Use the single wire clip to secure the wire from the pickup to the underside of the top and secure the cable into it. 3 Insert the supplied hexaphonic-saddle and secure it temporarily with a piece of tape. Pay attention that the bottom side of the saddle has to be absolutely flat. Make sure the 6 pickups showing towards the saddle. Push the Nanoflex 6 pickup from inside of guitar through the hole in the bridge and place the pickup into the bridge slot. Clean up the saddle slot and eliminate the wood dust and chips. ![]() Check your bracing before drilling the hole to avoid a damage of it. The hole has to be drilled in an angle of 30°-45°. Installation of Nanoflex and Nanoflex 6 Pickup: Take off the original saddle and drill a 3.1mm diameter hole in the corner of the saddle slot at the bass string side (see Fig.3). Tighten the hexagon nut with 12mm wrench and screw endpin strap nut on. Put the washer from the outside on the endpin jack. Adjust the inside nut so that the larger threads end just below the surface of the instrument (Fig. Remove endpin strap nut, hexagon nut and washer from the endpin (Fig. Remove original strap nut and increase hole up to 12,5mm diameter. Endpin Installation: Take off the strings, remove original strap nut and increase hole up to 12,5mm diameter. The battery LED lights on 30 minutes before need to be replaced. The preamps turn on automatically as soon as the guitar cable is plugged into the endpin. The systems are powered with 2 AAA 1,5V Batteries. ![]() We recommend installation by a professional. Installation: For all preamps you should start with the endpin installation, followed by the Nanoflex pickup installation and finished with the fitting of the preamp. The hexaphonic pickup Nanoflex-6 unites six Nanoflex pickups in one – one for each string. As a result of an enormous research and development effort over three years, Shadow releases a revolutionary pickup system. Shadow preamps are known for the most reliable, user-friendly and best sounding products on the market. Installation Instructions for SH 4020-A & SH 4020-C Introduction: Thank you and congratulations for choosing a Shadow pickup system.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |